| XinDian electric semi-automatic strapping | |
| Source：鑫电总经办 Click：16169 FreshTime：2011-05-11 08:23:56 | |
| Known or strapping strapping strapping machine, strapping tape winding using the product or package, and then tightened and both ends of the thermal effect of melting or by deduction and other materials connected with the package the machine. The function is to make the plastic strapping band can be tied closely to the surface of the package to ensure that packages in the transport, storage is not strong and not due to scattered bundles, neat appearance should also be tied. Semi-automatic strapping design features: 1. IC design: The new circuit design, packer plug-in circuit board with control over the entire packaged hot head movements and temperature, the circuit board replacement is convenient, baler service convenient. 2. Instant heating and immediate packaging: innovative design of high speed hot melt system, within 5 seconds to play hot piece of work can make the best packing PET baler into the state. 3. Automatic stopping devices, power utility: When packing action is completed, 60 seconds longer operation, the baler compact design, the motor will stop automatically into standby mode. 4. A new brake design: balers use the brakes with a disc with a special spring design to ensure smooth progress with no noise, balers and reasonable price. Principle and characteristics 1, the aircraft using the new integrated circuit, the access-type PC board to control the action throughout the subwoofer package design; 2, the whole combination of sound and mature, ultra-low noise, reduce stress; 3, packing speed, only 2.0 seconds per bale; instantaneous heating, heat 5 seconds to allow the work piece, into the best package state power utility; 4, the packing operation is completed within 60 seconds down at the standby mode, a new generation of electric steel design; 5, improved design, careful manufacture, use a wide range, regardless of the size of packaging, do not adjust the machine to be packaged; 6, the machine is a mechanical structure, some imported parts, after the blade is stable and reliable, and convenient adjustment; 7, the higher the packer table, easy to operate smoothly, suitable for packing lighter items. 8, no deformation of the characteristics of short-circuit packaging for a wide range; 9, the market of any packing tape, and from 6mm ~ 15mm, the best adhesion. IC design: The new circuit design, the use of plug-in circuit board control of the entire package hot head movements and temperature, circuit board replacement very convenient. Instant heating and immediate packaging: the first melt-speed thermal system design, can play within 5 seconds hot piece of work, packed into the best condition. Automatic shutdown devices, Power Saving Utility: When packing action is completed, 60 seconds is no longer operating, the motor will automatically stop, enter the standby mode. New brake design: The unit with the brake disc with a special spring design to ensure smooth with no noise into the Packer works Packer body is basically in the middle of packing, the first top-up the right, pressing with the front end, to tighten the tie strap on the object, and then left the top-up, pressed the appropriate place in the lower tape, heating tape between the two films into his , the increase in the top knife, cut off the tape, strapping tape to the last bit to the next, completing a cycle of work. Strapping is to use the package for winding products or packages, and then tighten the thermal effect and melting at both ends or by deduction and other materials connected with the package the machine. The function is to make the plastic strapping band can be tied closely to the surface of the package to ensure that packages in the transport, storage is not strong and not due to scattered bundles, neat appearance should also be tied. Packer workflow Ribbon tied to the digital signal received → → brake release, the main motor start (1) → Right up the top knife, withstood the right place with the slide (2) → "T"-type guide back (3) → proximity switch senses back with the probe (4) → main motor stops and the brake pull (5) → packer back with motor rotation, with 0.35 seconds back (6) → tape to tighten the tie to the object (7) → second start of main motor , brake pull (8) → large pendulum with a second pull to tighten the strap (9) → left parietal-up, the lower compression strap (10) → heating plate inserted into the middle of the two straps (11) → the top knife up, cut off the tape (12) → Knife in the top down (13) → the top knife again, and so firmly bonding the two tapes (14) → knife in the top down, so knives while the top down (15) → Heater reset ( 16) → slide back (17) → "T"-type guide Reset (18) → proximity switch sensors to send with a probe (19) → sent with the motor starts to drive tape sent with (20) → large pendulum reset (21) → tape in place, with head to the "T" type of guide plate (22) → close to the switch to dual-probe sensor (23) → main motor stops and the brake pull (24) → packer completion of a cycle of work. Packer workflow Ribbon tied to the digital signal received → → brake release, the main motor start (1) → Right up the top knife, withstood the right place with the slide (2) → "T"-type guide back (3) → proximity switch senses back with the probe (4) → main motor stops and the brake pull (5) → packer back with motor rotation, with 0.35 seconds back (6) → tape to tighten the tie to the object (7) → second start of main motor , brake pull (8) → large pendulum with a second pull to tighten the strap (9) → left parietal-up, the lower compression strap (10) → heating plate inserted into the middle of the two straps (11) → the top knife up, cut off the tape (12) → Knife in the top down (13) → the top knife again, and so firmly bonding the two tapes (14) → knife in the top down, so knives while the top down (15) → Heater reset ( 16) → slide back (17) → "T"-type guide Reset (18) → proximity switch sensors to send with a probe (19) → sent with the motor starts to drive tape sent with (20) → large pendulum reset (21) → tape in place, with head to the "T" type of guide plate (22) → close to the switch to dual-probe sensor (23) → main motor stops and the brake pull (24) → packer completion of a cycle of work. Note packer used 1. Make sure that the power used by the machine, do not plug the wrong power supply. The machine adopts three-phase four-wire system. Flowers line the zero line for the ground for leakage protection. 2. When you do not hand through the tape head of the runway. 3. Do not directly touch the heating plate by hand. 4. Do not machine wash with water, wet the workplace, the operators do not work barefoot. 5. Please storage when not in use the machine with the tape storage volumes back to the reel to prevent deformation of the next use. 6. Do not lose the wheel with the surface of viscous oil 7. Remember to unplug the machine when not in use. 8. Not free to replace the machine parts. 9. The main components to regular oil lubrication. Status of Chinese Packaging Machinery Packaging Machinery in China started late, after 20 years of development, China | |
| Pre：Xin electric sealing machine Product Description Next：suggestions to do packaging design |
| 【Top】【Print】【Back】 |
